Robotics_Tall banner_02

Position Detection in Drill Production With an In-Sight Vision System

DreBo Werkzeugfabrik GmbH

Industry:
ライフサイエンス
    Location:
    Altshausen, Germany
      Customer Objectives:
      • Maintain high product quality and renowned reputation
      • Monitor part positioning so milling can be performed at the correct working angle
      Key Results:
      • Reliably and accurately located parts, even with changing angles, sizes, and shading
      • Accelerated the milling process at crucial points and manufactured high volumes without problems
      • Saved critical floor space with compact vision system
      Cognex Solution:

      Sophisticated automation solutions are required in the high-quality manufacturing of drills. In order to accomplish this successfully, these automation solutions must be applied both to the design of the processes and to the identification and evaluation of the parts. As a leading manufacturer of carbide-tipped rock drills, DreBo Werkzeugfabrik GmbH in Altshausen, Germany has distinguished itself internationally for its high quality. To maintain this reputation DreBo relies on 2D Machine Vision Systems from Cognex.

      Up to 20,000 drills with diameters from 3 to 24 mm (0.12-0.95 inches) and lengths of 85 to 1000 mm (3.35-39.37 inches) pass through the bus-sized milling machines at DreBo. Particular emphasis is placed here on achieving the perfect combination of the drill with the carbide metal plate. In the first and the last processing stage, In-Sight vision systems from Cognex monitor the position of the parts to be processed.

      Correct positioning in the process

      On entering the milling machines, the unmachined parts fed from a magazine over a plate conveyor consist of a drill shaft and a drill spiral with an unprocessed drill head. This is equipped with the carbide metal plate only at the output of the machine. At the input of the machine, the In-Sight vision system detects the correct position of the unmachined parts using different gray levels of the smooth drill shaft and the drill spiral.  When the position is not correct, two parallel running swivel grippers turn the unmachined parts 180 degrees into the correct position.

      The drills arrive at the stamping station on a timed belt. Depending on the product type, the stamping slide applies information showing the diameter and the product and brand names. In the following head alignment station, the exact positioning of the unfinished drill head is performed at the correct working angle, so that it is subsequently possible to perform the milling of the head geometry and the plate slot for the insertion of the carbide metal plate.

      Exact seat in frictional connection

      In the subsequent two milling stations, the machine removes the first two roof surfaces, then follows the milling of the next two roof surfaces at an angle of 60°. Then the machine provides the head with a slit for the subsequent insertion of the carbide metal plate, the milling is deburred and, for better grip of the carbide metal plate, is notched on the inside. Until the final soldering, a frictional hold is present.

      Next comes the crucial step: the insertion of the carbide metal plate which transforms the unmachined part into a high-quality drill.  A SCARA robot picks up the plates from the conveyor by means of a pneumatic suction head and places them in a working form, which then inserts them into the notched gap in the drill head. The position coordinates for the entire process step are provided by the second Cognex vision system.

      Angles without drawbacks

      The most important tool provided by the In-Sight vision system is the geometric pattern matching capabilities from PatMax®. This vision tool locates the parts reliably and accurately, even under the toughest conditions. The geometry of an object is recorded using multiple boundary curves. PatMax is not tied to fixed pixel grids and can therefore look for similar shapes in the image, without having to rely on specific gray levels.

      Even with changing angles, sizes, and shading, the In-Sight vision system can locate the carbide metal plates reliably and accurately. The space-saving and robust vision systems accelerate the milling process at the crucial points, so that the DreBo milling machine can manufacture high volumes without problems.


      注目のコグネックス製品

      製品のサポートやトレーニングなどの詳細を見る

      マイコグネックスに参加

      お気軽にお問合せください

      Cognex は世界中でお客様のビジョンと工業用バーコドリーダのあらゆるニーズをサポートしています。

      お問合わせ